Gypsum tiles have to be laid properly, as not just the aesthetic appearance of decorative facing, but also the service quality of
the substance will depend on the engineering of job. The product is universal, and it can be attached to plaster, concrete, brick
or gypsum board sheets, provided the surface of the foundation is and has no defects.
If the defects of this foundation are important, it ought to be thoroughly treated with primer, then a cement mortar is created,
which satisfies all the cracks. Subsequently the surface ought to be primed and dried. Primer therapy is essential to improve the
bond between the tile and the walls. In this case, its composition should decide on a particular, containing elements which block
the look of fungus and mold.
In the modern interior of the rooms most frequently used gypsum tiles, imitating natural brick or stone. To perform cosmetic
finishing yourself, it is essential firstly to pick a scheme of tile positioning and prepare a remedy. It’s very important to pay
attention to the reverse side of the substance. If its surface has an embossed surface, then the glue ought to be placed using an
even trowel, and if it’s even, then using a notched one.
The technologies of this work is as follows:
* A thin layer of glue mortar is put on the pre-prepared wall. It’s spread over the base so it is likely to place 4-5 tiles.
Decorative cladding may be placed either on plasterboard, and on putty.
* Glue the back side of the tiles with adhesive.
* Plaster components are pushed against the wall and their place is adjusted. To align the seams, it is masterfasada.ru suggested to use
spacers.
* Finishing is carried out in rows, each of which ought to be changed by half a tile. Facing is carried out to the corners of
this room, and then immediately get rid of any residual mortar at the joints.
Drying the walls requires no more than a day and needs a continuous humidity and temperature inside the room. The final point in
the laying of gypsum tiles is that their decoration. To get this done, the joints between the elements are filled with a
particular solution, the color of which suits the brick.
Decorative imitation of brickwork around the walls will be completed in the following ways:
* Cutting on the plastered surface of the seams of masonry with a bolt cutter along with your hands;
* placing of tiles beneath the brick:
* mimicking the structure and color of the side of one brick;
* Imitating a fragment of brickwork of several bricks.
The best approach to decorate”beneath the brick” will be the one which enables you to make a usable coating with the most look of
its similarity to natural masonry. All 3 ways to carry out this sort of finishing works fulfill the prerequisites, but the cutting
of joints with a bolt is more labor-intensive and also the formation of large quantities of dust, and so let us consider more
common ways.
The old finish is removed from the walls, and also the surface, if needed, is leveled to get rid of the requirement to glue
plaster on a thick coating of adhesive.
Combining such cladding with other types of interior finishes may be both systematic and done without any clear consequences,
chaotically, together with fake of indications of aging.
With the help of cosmetic gypsum tiles it’s possible to imitate a large number of textures.
A large number of textures could be imitated with the help of decorative gypsum tiles.
The wall where it is to be installed must possess the following attributes:
* Hardness and intensity of the surface;
* The lack of uneven locations and sharp gaps;
* no deformations.
Cosmetic tiles in the interior of this kitchen
Walls are made from a variety of materials, let us break down the individual rules of installation.
When dealing with concrete, there’ll be no huge problems. It’s simply required to take into account the porosity of this material.
Concrete, that has nearly no pronounced pores, should be treated with a fantastic primer.
Mounting gypsum tiles on concrete
Before beginning work on the installation of gypsum tiles on the walls, it’s worth assessing the strength of this surface. After
the plaster does not drop off the wall and at exactly the exact same time holds nicely, you can simply paint it with primer.
Mount the tiles onto the painted concrete shouldn’t. The surface should be scratched, ensuring to misfire, then it should be
grouted and covered with a layer of plaster.
